ALTPLL (Phase-Locked Loop) IP Core User Guide

Download PDF
ID 683732
Date 6/16/2017
Public
Document Table of Contents
Document Table of Contents x
ALTPLL (Phase-Locked Loop) IP Core User Guide
ALTPLL (Phase-Locked Loop) IP Core User Guide x
ALTPLL Features Ports and Parameters Design Examples Document Revision History
ALTPLL Features x
Phase-Locked Loop Types of PLLs Operation Modes Output Clocks Advanced Features PLL Output Counter Cascading
Phase-Locked Loop x
Building Blocks of a PLL PLL Behavior
Types of PLLs x
Parameter Setting Total Number of PLL Available in Each Supported Device Family
Operation Modes x
Operation Modes Supported in Each Device Family Parameter Settings Determining the PLL Lock Range Expanding the PLL Lock Range Setting Up Stratix III and Stratix IV PLLs for LVDS Interfacing Simulating External Feedback Board Delay
Output Clocks x
Parameter Settings Parameter Settings When “Set up PLL in LVDS mode” Option is Enabled Summary of PLL Output Clocks
Advanced Features x
Advanced Control Signals (pllena, areset, pfdena) Clock Switchover Spread-Spectrum Clocking Gated Lock and Self-Reset Programmable Bandwidth Advanced PLL Parameters PLL Dynamic Reconfiguration Dynamic Phase Configuration
Advanced Control Signals (pllena, areset, pfdena) x
pllena areset pfdena Parameter Settings Summary of Advanced Control Signals
Clock Switchover x
Parameter Settings Summary of Automatic Clock Switchover Feature
Spread-Spectrum Clocking x
Parameter Settings Summary of Spread-Spectrum Clocking Feature
Gated Lock and Self-Reset x
Gated Lock Self-Reset on Loss of Lock Parameter Settings Calculating the Value of Gated Lock Counter Summary of Gated Lock Signals and Self-Reset on Loss of Lock
Programmable Bandwidth x
Parameter Settings Summary of Programmable Bandwidth Support
Advanced PLL Parameters x
Advanced Parameter Settings
PLL Dynamic Reconfiguration x
Parameter Settings Summary of Supported Device Families for PLL Dynamic Reconfiguration Feature
Dynamic Phase Configuration x
Supported Devices Parameter Settings Modifying the PLL Phase Shift Step Resolution Using Advanced Parameters
Ports and Parameters x
ALTPLL Input Ports ALTPLL Output Ports ALTPLL Bidirectional Port ALTPLL Parameters
Design Examples x
Design Files Design Example 1: Differential Clock Design Example 2: Generating Clock Signals
Design Example 1: Differential Clock x
Generating a 166-MHz Differential SSTL External Clock Implementing the ddr_clk Design Functional Results — Simulate the ddr_clk Design in the ModelSim®-Altera Software
Design Example 2: Generating Clock Signals x
Generating 133-MHz, 200-MHz, and 200-MHz Time-Shifted Clocks Implementing the shift_clk Design Simulating the shift_clk Design in the ModelSim-Altera Software
ALTPLL (Phase-Locked Loop) IP Core User Guide

Design Example 1: Differential Clock

This design example uses the ALTPLL IP core to generate an external differential clock from an enhanced PLL. You must generate or modify clock signals to meet design specifications. When you interface to double data rate (DDR) memory, you must generate a differential SSTL clock signal for the external device. A DDR DIMM requires three pairs of differential SSTL clocks. You can use enhanced PLLs in Stratix devices to generate these clock signals.

In this example, perform the following activities:

  • Generate a 166-MHz differential SSTL external clock (ddr_clk) output from a 33.33-MHz input clock using the ALTPLL IP core and the parameter editor.
  • Implement the DDR_CLK design by assigning the EP1S10F780 device to the project and compiling the project.
  • Simulate the DDR_CLK design.

Section Content
Generating a 166-MHz Differential SSTL External Clock
Implementing the ddr_clk Design
Functional Results — Simulate the ddr_clk Design in the ModelSim®-Altera Software

Level Two Title