Intel® Cyclone® 10 GX Device Datasheet

ID 683828
Date 2/14/2022
Public
Document Table of Contents

I/O PLL Specifications

Table 31.  I/O PLL Specifications for Intel® Cyclone® 10 GX Devices
Symbol Parameter Condition Min Typ Max Unit
fIN Input clock frequency –5 speed grade 10 700 53 MHz
–6 speed grade 10 650 53 MHz
fINPFD Input clock frequency to the PFD 10 325 MHz
fCASC_INPFD Input clock frequency to the PFD of destination cascade PLL 10 60 MHz
fVCO PLL VCO operating range –5 speed grade 600 1434 MHz
–6 speed grade 600 1250 MHz
fCLBW PLL closed-loop bandwidth 0.1 8 MHz
tEINDUTY Input clock or external feedback clock input duty cycle 40 60 %
fOUT Output frequency for internal global or regional clock (C counter) –5, –6 speed grade 644 MHz
fOUT_EXT Output frequency for external clock output –5 speed grade 720 MHz
–6 speed grade 650 MHz
tOUTDUTY Duty cycle for dedicated external clock output (when set to 50%) 45 50 55 %
tFCOMP External feedback clock compensation time 10 ns
fDYCONFIGCLK Dynamic configuration clock for mgmt_clk and scanclk 100 MHz
tLOCK Time required to lock from end-of-device configuration or deassertion of areset 1 ms
tDLOCK Time required to lock dynamically (after switchover or reconfiguring any non-post-scale counters/delays) 1 ms
tPLL_PSERR Accuracy of PLL phase shift ±50 ps
tARESET Minimum pulse width on the areset signal 10 ns
tINCCJ 54 55 Input clock cycle-to-cycle jitter FREF ≥ 100 MHz 0.15 UI (p-p)
FREF < 100 MHz 750 ps (p-p)
tOUTPJ_DC Period jitter for dedicated clock output FOUT ≥ 100 MHz 175 ps (p-p)
FOUT < 100 MHz 17.5 mUI (p-p)
tOUTCCJ_DC Cycle-to-cycle jitter for dedicated clock output FOUT ≥ 100 MHz 175 ps (p-p)
FOUT < 100 MHz 17.5 mUI (p-p)
tOUTPJ_IO 56 Period jitter for clock output on the regular I/O FOUT ≥ 100 MHz 600 ps (p-p)
FOUT < 100 MHz 60 mUI (p-p)
tOUTCCJ_IO 56 Cycle-to-cycle jitter for clock output on the regular I/O FOUT ≥ 100 MHz 600 ps (p-p)
FOUT < 100 MHz 60 mUI (p-p)
tCASC_OUTPJ_DC Period jitter for dedicated clock output in cascaded PLLs FOUT ≥ 100 MHz 175 ps (p-p)
FOUT < 100 MHz 17.5 mUI (p-p)
53 This specification is limited by the I/O maximum frequency. The maximum achievable I/O frequency is different for each I/O standard and is depends on design and system specific factors. Ensure proper timing closure in your design and perform HSPICE/IBIS simulations based on your specific design and system setup to determine the maximum achievable frequency in your system.
54 A high input jitter directly affects the PLL output jitter. To have low PLL output clock jitter, you must provide a clean clock source with jitter < 120 ps.
55 FREF is fIN/N, specification applies when N = 1.
56 External memory interface clock output jitter specifications use a different measurement method, which are available in Memory Output Clock Jitter Specification for Intel® Cyclone® 10 GX Devices table.