Arria® 10 Transceiver PHY User Guide

ID 683617
Date 4/01/2024
Public
Document Table of Contents

2.5.5. Native PHY IP Parameter Settings for Interlaken

This section contains the recommended parameter values for this protocol. Refer to Using the Arria 10 Transceiver Native PHY IP Core for the full range of parameter values.
Table 75.  General and Datapath Parameters

Parameter

Value

Message level for rule violations

error

warning

Transceiver configuration rules

Interlaken

PMA configuration rules basic

Transceiver mode

TX / RX Duplex

TX Simplex

RX Simplex

Number of data channels

1 to 96

Data rate

Up to 17.4 Gbps for GX devices

(Depending on Enhanced PCS to PMA interface width selection)

Enable datapath and interface reconfiguration

On / Off

Enable simplified data interface

On / Off

Provide separate interface for each channel

On / Off

Table 76.  TX PMA Parameters

Parameter

Value

TX channel bonding mode

Not bonded

PMA-only bonding

PMA and PCS bonding

PCS TX channel bonding master

If TX channel bonding mode is set to PMA and PCS bonding, then:

Auto, 0, 1, 2, 3 through [Number of data channels – 1]

Actual PCS TX channel bonding master

If TX channel bonding mode is set to PMA and PCS bonding, then:

0, 1, 2, 3 through [Number of data channels – 1]

TX local clock division factor

If TX channel bonding mode is not bonded, then:

1, 2, 4, 8

Number of TX PLL clock inputs per channel

If TX channel bonding mode is not bonded, then:

1, 2, 3, 4

Initial TX PLL clock input selection

0

Enable tx_pma_clkout port

On / Off

Enable tx_pma_div_clkout port

On / Off

tx_pma_div_clkout division factor

When Enable tx_pma_div_clkout port is On, then:

Disabled, 1, 2, 33, 40, 66

Enable tx_pma_elecidle port

On / Off

Enable tx_pma_qpipullup port (QPI)

Off

Enable tx_pma_qpipulldn port (QPI)

Off

Enable tx_pma_txdetectrx port (QPI)

Off

Enable tx_pma_rxfound port (QPI)

Off

Enable rx_seriallpbken port

On / Off

Table 77.  RX PMA Parameters

Parameter

Value

Number of CDR reference clocks

1 to 5

Selected CDR reference clock

0 to 4

Selected CDR reference clock frequency

Select legal range defined by the Quartus Prime software

PPM detector threshold

100, 300, 500, 1000

CTLE adaptation mode

manual,

DFE adaptation mode

adaptation enabled, manual, disabled

Number of fixed dfe taps

3, 7, 11

Enable rx_pma_clkout port

On / Off

Enable rx_pma_div_clkout port

On / Off

rx_pma_div_clkout division factor

When Enable rx_pma_div_clkout port is On, then:

Disabled, 1, 2, 33, 40, 66

Enable rx_pma_clkslip port

On / Off

Enable rx_pma_qpipulldn port (QPI)

Off

Enable rx_is_lockedtodata port

On / Off

Enable rx_is_lockedtoref port

On / Off

Enable rx_set_locktodata and rx_set_locktoref ports

On / Off

Enable rx_seriallpbken port

On / Off

Enable PRBS verifier control and status ports

On / Off

Table 78.  Enhanced PCS Parameters

Parameter

Value

Enhanced PCS / PMA interface width

32, 40, 64

FPGA fabric / Enhanced PCS interface width

67

Enable 'Enhanced PCS' low latency mode

Allowed when the PMA interface width is 32 and preset variations for data rate is 10.3125 Gbps or 6.25 Gbps; otherwise Off

Enable RX/TX FIFO double-width mode

Off

TX FIFO mode

Interlaken

TX FIFO partially full threshold

8 to 15

TX FIFO partially empty threshold

1 to 8

Enable tx_enh_fifo_full port

On / Off

Enable tx_enh_fifo_pfull port

On / Off

Enable tx_enh_fifo_empty port

On / Off

Enable tx_enh_fifo_pempty port

On / Off

RX FIFO mode

Interlaken

RX FIFO partially full threshold

from 10-29 (no less than pempty_threshold+8)

RX FIFO partially empty threshold

2 to 10

Enable RX FIFO alignment word deletion (Interlaken)

On / Off

Enable RX FIFO control word deletion (Interlaken)

On / Off

Enable rx_enh_data_valid port

On / Off

Enable rx_enh_fifo_full port

On / Off

Enable rx_enh_fifo_pfull port

On / Off

Enable rx_enh_fifo_empty port

On / Off

Enable rx_enh_fifo_pempty port

On / Off

Enable rx_enh_fifo_del port (10GBASE-R)

Off

Enable rx_enh_fifo_insert port (10GBASE-R)

Off

Enable rx_enh_fifo_rd_en port

On

Enable rx_enh_fifo_align_val port (Interlaken)

On / Off

Enable rx_enh_fifo_align_clr port (Interlaken)

On

Table 79.  Interlaken Frame Generator Parameters

Parameter

Value

Enable Interlaken frame generator

On

Frame generator metaframe length

5 to 8192 (Intel recommends a minimum metaframe length of 128)

Enable frame generator burst control

On

Enable tx_enh_frame port

On

Enable tx_enh_frame_diag_status port

On

Enable tx_enh_frame_burst_en port

On

Table 80.  Interlaken Frame Synchronizer Parameters

Parameter

Value

Enable Interlaken frame synchronizer

On

Frame synchronizer metaframe length

5 to 8192 (Intel recommends a minimum metaframe length of 128)

Enable rx_enh_frame port

On

Enable rx_enh_frame_lock port

On / Off

Enable rx_enh_frame_diag_status port

On / Off

Table 81.  Interlaken CRC-32 Generator and Checker Parameters

Parameter

Value

Enable Interlaken TX CRC-32 generator

On

Enable Interlaken TX CRC-32 generator error insertion

On / Off

Enable Interlaken RX CRC-32 checker

On

Enable rx_enh_crc32_err port

On / Off

Table 82.  Scrambler and Descrambler Parameters

Parameter

Value

Enable TX scrambler (10GBASE-R / Interlaken)

On

TX scrambler seed (10GBASE-R / Interlaken)

0x1 to 0x3FFFFFFFFFFFFFF

Enable RX descrambler (10GBASE-R / Interlaken)

On

Table 83.  Interlaken Disparity Generator and Checker Parameters

Parameter

Value

Enable Interlaken TX disparity generator

On

Enable Interlaken RX disparity checker

On

Enable Interlaken TX random disparity bit

On / Off

Table 84.  Block Sync Parameters

Parameter

Value

Enable RX block synchronizer

On

Enable rx_enh_blk_lock port

On / Off

Table 85.  Gearbox Parameters

Parameter

Value

Enable TX data bitslip

Off

Enable TX data polarity inversion

On / Off

Enable RX data bitslip

Off

Enable RX data polarity inversion

On / Off

Enable tx_enh_bitslip port

Off

Enable rx_bitslip port

Off

Table 86.  Dynamic Reconfiguration Parameters

Parameter

Value

Enable dynamic reconfiguration

On / Off

Share reconfiguration interface

On / Off

Enable Native PHY Debug Master Endpoint

On / Off

Separate reconfig_waitrequest from the status of AVMM arbitration with PreSICE

On / Off

Enable capability registers

On / Off

Set user-defined IP identifier:

0 to 255

Enable control and status registers

On / Off

Enable prbs soft accumulators

On / Off

Table 87.  Configuration Files Parameters

Parameter

Value

Configuration file prefix

Generate SystemVerilog package file

On / Off

Generate C header file

On / Off

Generate MIF (Memory Initialization File)

On / Off

Include PMA analog settings in configuration files

On / Off

Table 88.  Configuration Profiles Parameters

Parameter

Value

Enable multiple reconfiguration profiles

On / Off

Enable embedded reconfiguration streamer

On / Off

Generate reduced reconfiguration files

On / Off

Number of reconfiguration profiles

1 to 8

Selected reconfiguration profile

1 to 7