Intel Agilex® 7 FPGA F-Series Transceiver-SoC Development Kit User Guide

Download PDF
ID 683752
Date 4/21/2023
Public
Document Table of Contents
Document Table of Contents x
1. Overview 2. Getting Started 3. Powering Up the Development Kit 4. Board Test System 5. Development Kit Hardware and Configuration 6. Custom Projects for the Development Kit 7. Revision History A. Development Kit Components B. Additional Information
1. Overview x
1.1. Block Diagram 1.2. Feature Summary 1.3. Box Contents 1.4. Recommended Operating Conditions
2. Getting Started x
2.1. Intel® Quartus® Prime Software and Driver Installation 2.2. Quick Start Guide 2.3. Design Examples
3. Powering Up the Development Kit x
3.1. Default Settings 3.2. Power Up 3.3. Perform board restore
3.3. Perform board restore x
3.3.1. Restore board System Intel® MAX® 10 with default factory image 3.3.2. Restore board QSPI flash with the default factory image
4. Board Test System x
4.1. Setting Up the BTS GUI Running Environment 4.2. Test the functionality of the Development Kits 4.3. Control on-board clock through Clock Controller GUI 4.4. Control on-board power regulator through Power Monitor GUI
4.1. Setting Up the BTS GUI Running Environment x
4.1.1. Downloading OpenJDK 4.1.2. Downloading OpenJFX 4.1.3. Installing OpenJDK and OpenJFX 4.1.4. Installing the Quartus Prime Software 4.1.5. Running the BTS GUI
4.2. Test the functionality of the Development Kits x
4.2.1. The Configure Menu 4.2.2. The Sys Info Tab 4.2.3. The GPIO Tab 4.2.4. The XCVR Tab 4.2.5. The DDR4 Tab 4.2.6. The SSS Tab 4.2.7. The EEPROM Tab
5. Development Kit Hardware and Configuration x
5.1. Configure FPGA and access HPS Debug Access Port by JTAG 5.2. Configure the FPGA device by AS modes (Default Mode) 5.3. Configure the FPGA device by AvST modes 5.4. Daughter Cards
5.4. Daughter Cards x
5.4.1. HPS Out of Box Experience (OOBE) Daughter Card 5.4.2. HPS NAND Daughter Card
6. Custom Projects for the Development Kit x
6.1. Add SmartVID settings in Intel® Quartus® Prime QSF file 6.2. Golden Top
A. Development Kit Components x
A.1. System Management A.2. Power A.3. Clocks A.4. General Input/Output A.5. Memory Interfaces A.6. Communication Interfaces A.7. Daughter Cards
B. Additional Information x
B.1. Safety and Regulatory Information B.2. Compliance Information
B.1. Safety and Regulatory Information x
B.1.1. Safety Warnings B.1.2. Safety Cautions
1. Overview
2. Getting Started
3. Powering Up the Development Kit
4. Board Test System
5. Development Kit Hardware and Configuration
6. Custom Projects for the Development Kit
7. Revision History
A. Development Kit Components
B. Additional Information

5.1. Configure FPGA and access HPS Debug Access Port by JTAG

  1. JTAG access does not rely on SW1 settings and system image.
  2. Plug the USB cable to CN1 or Intel® FPGA Download Cable to J19.
  3. Open Intel® Quartus® Prime Programmer, system console to configuration Intel Agilex® 7 FPGA SDM, system Intel® MAX® 10 and PCIe JTAG nodes.
  4. Open Arm* Development Studio 5* (DS-5*) Intel SoC FPGA Edition to connect to and communicate with the HPS Debug Access Port (DAP) through the same JTAG interface.
    Note: By default, HPS and FPGA SDM JTAG nodes are chained together internally. SW3.1 bypasses or enables both nodes at the same time. OOBE’s Mictor 38-pin header cannot access HPS DAP function.

    If attestation and/or Black Key Provisioning (BKP) is enabled on the Intel Agilex® 7 device, you must use the updated SDM firmware and TCK guidelines (JTAG clock).

    • You must update to the SDM firmware delivered with the Intel® Quartus® Prime Pro Edition version 21.3 and beyond.
    • For the TCK pin, you must either leave the TCK pin unconnected, or connect the TCK pin to the VCCIO_SDM supply using a 10-kΩ pull-up resistor.
    Note: The existing guidance in the Intel Agilex® 7 Device Family Pin Connection Guidelines to connect TCK to a 1-kΩ pull-down resistor is included for noise suppression. The change in guidance to a 10-kΩ pull-up resistor is not expected to affect the device functionally.

    For more information about connecting the TCK pin, refer to the Intel Agilex® 7 Device Family Pin Connection Guidelines.

Level Two Title