Shared 3V I/O Bank Pins
Note: Intel® recommends that you create a Intel® Quartus® Prime design, enter your device I/O assignments, and compile the design. The Intel® Quartus® Prime software will check your pin connections according to I/O assignment and placement rules. The rules differ from one device to another based on device density, package, I/O assignments, voltage assignments, and other factors that are not fully described in this document or the device handbook.
| HPS Pin Name | Pin Type | Pin Functions See Notes 16 and 17. |
Pin Description | Connection Guidelines |
|---|---|---|---|---|
| HPS_Shared_Q1_1 | I/O | Pin Mux Select 2 | SPIS0 Clock | If unused, program it in the Intel® Quartus® Prime software as an input with a weak pull-up. When you are using this pin for the SD/MMC/eMMC device, pull this pin high on the board with a weak pull-up resistor such as 10-kΩ. |
| Pin Mux Select 3 | SPIM0 Slave Select 1 See Note 19. |
|||
| Pin Mux Select 4 | SDMMC Data Bit 0 | |||
| Pin Mux Select 8 | USB0 Clock | |||
| Pin Mux Select 13 | UART0 Clear to Send See Note 19. |
|||
| Pin Mux Select 14 | NAND Data Bit 0 | |||
| Pin Mux Select 15 See Note 18. |
GPIO 0 Bit 0 | |||
| HPS_Shared_Q1_2 | I/O | Pin Mux Select 2 | SPIS 0 Master Out Slave In | If unused, program it in the Intel® Quartus® Prime software as an input with a weak pull-up. When you are using this pin for the SD/MMC/eMMC device, pull this pin high on the board with a weak pull-up resistor such as 10-kΩ. |
| Pin Mux Select 3 | SPIM 1 Slave Select 1 See Note 19. |
|||
| Pin Mux Select 4 | SDMMC Command Line | |||
| Pin Mux Select 8 | USB 0 Stop Data | |||
| Pin Mux Select 13 | UART 0 Request to Send See Note 19. |
|||
| Pin Mux Select 14 | NAND Data Bit 1 | |||
| Pin Mux Select 15 See Note 18. |
GPIO 0 Bit 1 | |||
| HPS_Shared_Q1_3 | I/O | Pin Mux Select 0 | I2C 1 Serial Data | If unused, program it in the Intel® Quartus® Prime software as an input with a weak pull-up. |
| Pin Mux Select 2 | SPIS 0 Slave Select 0 See Note 19. |
|||
| Pin Mux Select 4 | SDMMC Clock Out | |||
| Pin Mux Select 8 | USB 0 Direction | |||
| Pin Mux Select 13 | UART 0 Transmit | |||
| Pin Mux Select 14 | NAND Write Enable See Note 19. |
|||
| Pin Mux Select 15 See Note 18. |
GPIO 0 Bit 2 | |||
| HPS_Shared_Q1_4 | I/O | Pin Mux Select 0 | I2C 1 Serial Clock | If unused, program it in the Intel® Quartus® Prime software as an input with a weak pull-up. When you are using this pin for the SD/MMC/eMMC device, pull this pin high on the board with a weak pull-up resistor such as 10-kΩ. |
| Pin Mux Select 2 | SPIS 0 Master In Slave Out | |||
| Pin Mux Select 4 | SDMMC Data Bit 1 | |||
| Pin Mux Select 8 | USB 0 Data Bit 0 | |||
| Pin Mux Select 13 | UART 0 Receive | |||
| Pin Mux Select 14 | NAND Read Enable See Note 19. |
|||
| Pin Mux Select 15 See Note 18. |
GPIO 0 Bit 3 | |||
| HPS_Shared_Q1_5 | I/O | Pin Mux Select 0 | I2C 0 Serial Data | If unused, program it in the Intel® Quartus® Prime software as an input with a weak pull-up. When you are using this pin for the SD/MMC/eMMC device, pull this pin high on the board with a weak pull-up resistor such as 10-kΩ. |
| Pin Mux Select 3 | SPIM 0 Clock | |||
| Pin Mux Select 4 | SDMMC Data Bit 2 | |||
| Pin Mux Select 8 | USB0 Data Bit 1 | |||
| Pin Mux Select 12 | QSPI Slave Select 2 | |||
| Pin Mux Select 13 | UART 1 Clear to Send See Note 19. |
|||
| Pin Mux Select 14 | NAND Write Protect See Note 19. |
|||
| Pin Mux Select 15 See Note 18. |
GPIO 0 Bit 4 | |||
| HPS_Shared_Q1_6 | I/O | Pin Mux Select 0 | I2C 0 Serial Clock | If unused, program it in the Intel® Quartus® Prime software as an input with a weak pull-up. When you are using this pin for the SD/MMC/eMMC device, pull this pin high on the board with a weak pull-up resistor such as 10-kΩ. The SD card has an internal pull-up on the SDMMC Data Bit 3 that can be disabled in the software using the SET_CLR_CARD_DETECT (ACMD42) command. This is not applicable for the MMC/eMMC flash. |
| Pin Mux Select 3 | SPIM 0 Master Out Slave In | |||
| Pin Mux Select 4 | SDMMC Data Bit 3 | |||
| Pin Mux Select 8 | USB 0 Next Data | |||
| Pin Mux Select 12 | QSPI Slave Select 3 | |||
| Pin Mux Select 13 | UART 1 Request to Send See Note 19. |
|||
| Pin Mux Select 14 | NAND Data Bit 2 | |||
| Pin Mux Select 15 See Note 18. |
GPIO 0 Bit 5 | |||
| HPS_Shared_Q1_7 | I/O | Pin Mux Select 0 | I2C EMAC 2 Serial Data | If unused, program it in the Intel® Quartus® Prime software as an input with a weak pull-up. When you are using this pin for the MMC/eMMC device, pull this pin high on the board with a weak pull-up resistor such as 10-kΩ. |
| Pin Mux Select 1 | EMAC 2 MDIO | |||
| Pin Mux Select 3 | SPIM 0 Master In SlaveOut | |||
| Pin Mux Select 4 | SDMMC Data Bit 4 | |||
| Pin Mux Select 8 | USB0 Data Bit 2 | |||
| Pin Mux Select 13 | UART 1 Transmit | |||
| Pin Mux Select 14 | NAND Data Bit 3 | |||
| Pin Mux Select 15 See Note 18. |
GPIO 0 Bit 6 | |||
| HPS_Shared_Q1_8 | I/O | Pin Mux Select 0 | I2C EMAC 2 Serial Clock | If unused, program it in the Intel® Quartus® Prime software as an input with a weak pull-up. When you are using this pin for the MMC/eMMC device, pull this pin high on the board with a weak pull-up resistor such as 10-kΩ. |
| Pin Mux Select 1 | EMAC 2 MDC | |||
| Pin Mux Select 3 | SPIM 0 Slave Select 0 See Note 19. |
|||
| Pin Mux Select 4 | SDMMC Data Bit 5 | |||
| Pin Mux Select 8 | USB 0 Data Bit 3 | |||
| Pin Mux Select 13 | UART 1 Receive | |||
| Pin Mux Select 14 | NAND Command Latch Enable | |||
| Pin Mux Select 15 See Note 18. |
GPIO 0 Bit 7 | |||
| HPS_Shared_Q1_9 | I/O | Pin Mux Select 0 | I2C EMAC 1 Serial Data | If unused, program it in the Intel® Quartus® Prime software as an input with a weak pull-up. When you are using this pin for the MMC/eMMC device, pull this pin high on the board with a weak pull-up resistor such as 10-kΩ. |
| Pin Mux Select 1 | EMAC 1 MDIO | |||
| Pin Mux Select 2 | SPIS 1 Clock | |||
| Pin Mux Select 3 | SPIM 1 Clock | |||
| Pin Mux Select 4 | SDMMC Data Bit 6 | |||
| Pin Mux Select 8 | USB 0 Data Bit 4 | |||
| Pin Mux Select 14 | NAND Data Bit 4 | |||
| Pin Mux Select 15 See Note 18. |
GPIO 0 Bit 8 | |||
| HPS_Shared_Q1_10 | I/O | Pin Mux Select 0 | I2C EMAC 1 Serial Clock | If unused, program it in the Intel® Quartus® Prime software as an input with a weak pull-up. When you are using this pin for the MMC/eMMC device, pull this pin high on the board with a weak pull-up resistor such as 10-kΩ. |
| Pin Mux Select 1 | EMAC 1 MDC | |||
| Pin Mux Select 2 | SPIS 1 Master Out Slave In | |||
| Pin Mux Select 3 | SPIM 1 Master Out Slave In | |||
| Pin Mux Select 4 | SDMMC Data Bit 7 | |||
| Pin Mux Select 8 | USB 0 Data Bit 5 | |||
| Pin Mux Select 14 | NAND Data Bit 5 | |||
| Pin Mux Select 15 See Note 18. |
GPIO 0 Bit 9 | |||
| HPS_Shared_Q1_11 | I/O | Pin Mux Select 0 | I2C EMAC 0 Serial Data | If unused, program it in the Intel® Quartus® Prime software as an input with a weak pull-up. When you are using this pin for the MMC/eMMC device, pull this pin high on the board with a weak pull-up resistor such as 10-kΩ. |
| Pin Mux Select 1 | EMAC 0 MDIO | |||
| Pin Mux Select 2 | SPIS 1 Slave Select 0 See Note 19. |
|||
| Pin Mux Select 3 | SPIM 1 Master In Slave Out | |||
| Pin Mux Select 8 | USB 0 Data Bit 6 | |||
| Pin Mux Select 14 | NAND Data Bit 6 | |||
| Pin Mux Select 15 See Note 18. |
GPIO 0 Bit 10 | |||
| HPS_Shared_Q1_12 | I/O | Pin Mux Select 0 | I2C EMAC 0 Serial Clock | If unused, program it in the Intel® Quartus® Prime software as an input with a weak pull-up. |
| Pin Mux Select 1 | EMAC 0 MDC | |||
| Pin Mux Select 2 | SPIS 1 Master In Slave Out | |||
| Pin Mux Select 3 | SPIM 1 Slave Select 0 See Note 19. |
|||
| Pin Mux Select 8 | USB 0 Data Bit 7 | |||
| Pin Mux Select 14 | NAND Data Bit 7 | |||
| Pin Mux Select 15 See Note 18. |
GPIO 0 Bit 11 | |||
| HPS_Shared_Q2_1 | I/O | Pin Mux Select 4 | EMAC 0 Transmit Clock | If unused, program it in the Intel® Quartus® Prime software as an input with a weak pull-up. |
| Pin Mux Select 8 | USB 1 Clock | |||
| Pin Mux Select 14 | NAND Address Latch Enable | |||
| Pin Mux Select 15 See Note 18. |
GPIO 0 Bit 12 | |||
| HPS_Shared_Q2_2 | I/O | Pin Mux Select 4 | EMAC 0 Transmit Control | If used as the NAND Ready/Busy input, connect this pin through a pull-up resistor to VCCIO_2L in the dedicated I/O bank which the NAND_RB pin resides. For more information of the pull-up resistor value, refer to the NAND flash specification. If unused, program it in the Intel® Quartus® Prime software as an input with a weak pull-up. |
| Pin Mux Select 8 | USB 1 Stop Data | |||
| Pin Mux Select 14 | NAND Ready/Busy | |||
| Pin Mux Select 15 See Note 18. |
GPIO 0 Bit 13 | |||
| HPS_Shared_Q2_3 | I/O | Pin Mux Select 4 | EMAC 0 Receive Clock | If unused, program it in the Intel® Quartus® Prime software as an input with a weak pull-up. |
| Pin Mux Select 8 | USB 1 Direction | |||
| Pin Mux Select 14 | NAND Chip Enable See Note 19. |
|||
| Pin Mux Select 15 See Note 18. |
GPIO 0 Bit 14 | |||
| HPS_Shared_Q2_4 | I/O | Pin Mux Select 4 | EMAC 0 Receive Control | If unused, program it in the Intel® Quartus® Prime software as an input with a weak pull-up. |
| Pin Mux Select 8 | USB 1 Data Bit 0 | |||
| Pin Mux Select 15 See Note 18. |
GPIO 0 Bit 15 | |||
| HPS_Shared_Q2_5 | I/O | Pin Mux Select 4 | EMAC 0 Transmit Data Bit 0 | If unused, program it in the Intel® Quartus® Prime software as an input with a weak pull-up. |
| Pin Mux Select 8 | USB 1 Data Bit 1 | |||
| Pin Mux Select 14 | NAND Data Bit 8 | |||
| Pin Mux Select 15 See Note 18. |
GPIO 0 Bit 16 | |||
| HPS_Shared_Q2_6 | I/O | Pin Mux Select 4 | EMAC 0 Transmit Data Bit 1 | If unused, program it in the Intel® Quartus® Prime software as an input with a weak pull-up. |
| Pin Mux Select 8 | USB 1 Next Data | |||
| Pin Mux Select 14 | NAND Data Bit 9 | |||
| Pin Mux Select 15 See Note 18. |
GPIO 0 Bit 17 | |||
| HPS_Shared_Q2_7 | I/O | Pin Mux Select 4 | EMAC0 Receive Data Bit 0 | If unused, program it in the Intel® Quartus® Prime software as an input with a weak pull-up. |
| Pin Mux Select 8 | USB1 Data Bit 2 | |||
| Pin Mux Select 14 | NAND Data Bit 10 | |||
| Pin Mux Select 15 See Note 18. |
GPIO0 Bit 18 | |||
| HPS_Shared_Q2_8 | I/O | Pin Mux Select 3 | SPIM 1 Slave Select 1 See Note 19. |
If unused, program it in the Intel® Quartus® Prime software as an input with a weak pull-up. |
| Pin Mux Select 4 | EMAC 0 Receive Data Bit 1 | |||
| Pin Mux Select 8 | USB 1 Data Bit 3 | |||
| Pin Mux Select 14 | NAND Data Bit 11 | |||
| Pin Mux Select 15 See Note 18. |
GPIO 0 Bit 19 | |||
| HPS_Shared_Q2_9 | I/O | Pin Mux Select 0 | I2C 1 Serial Data | If unused, program it in the Intel® Quartus® Prime software as an input with a weak pull-up. |
| Pin Mux Select 2 | SPIS 0 Clock | |||
| Pin Mux Select 3 | SPIM 1 Clock | |||
| Pin Mux Select 4 | EMAC 0 Transmit Data Bit 2 | |||
| Pin Mux Select 8 | USB 1 Data Bit 4 | |||
| Pin Mux Select 13 | UART 0 Clear to Send See Note 19. |
|||
| Pin Mux Select 14 | NAND Data Bit 12 | |||
| Pin Mux Select 15 See Note 18. |
GPIO 0 Bit 20 | |||
| HPS_Shared_Q2_10 | I/O | Pin Mux Select 0 | I2C 1 Serial Clock | If unused, program it in the Intel® Quartus® Prime software as an input with a weak pull-up. |
| Pin Mux Select 2 | SPIS 0 Master Out Slave In | |||
| Pin Mux Select 3 | SPIM 1 Master Out Slave In | |||
| Pin Mux Select 4 | EMAC 0 Transmit Data Bit 3 | |||
| Pin Mux Select 8 | USB 1 Data Bit 5 | |||
| Pin Mux Select 13 | UART 0 Request to Send See Note 19. |
|||
| Pin Mux Select 14 | NAND Data Bit 13 | |||
| Pin Mux Select 15 See Note 18. |
GPIO 0 Bit 21 | |||
| HPS_Shared_Q2_11 | I/O | Pin Mux Select 0 | I2C 0 Serial Data | If unused, program it in the Intel® Quartus® Prime software as an input with a weak pull-up. |
| Pin Mux Select 2 | SPIS 0 Slave Select 0 See Note 19. |
|||
| Pin Mux Select 3 | SPIM 1 Master In Slave Out | |||
| Pin Mux Select 4 | EMAC 0 Receive Data Bit 2 | |||
| Pin Mux Select 8 | USB 1 Data Bit 6 | |||
| Pin Mux Select 13 | UART 0 Transmit | |||
| Pin Mux Select 14 | NAND Data Bit 14 | |||
| Pin Mux Select 15 See Note 18. |
GPIO 0 Bit 22 | |||
| HPS_Shared_Q2_12 | I/O | Pin Mux Select 0 | I2C0 Serial Clock | If unused, program it in the Intel® Quartus® Prime software as an input with a weak pull-up. |
| Pin Mux Select 2 | SPIS0 Master In Slave Out | |||
| Pin Mux Select 3 | SPIM1 Slave Select 0 See Note 19. |
|||
| Pin Mux Select 4 | EMAC0 Receive Data Bit 3 | |||
| Pin Mux Select 8 | USB1 Data Bit 7 | |||
| Pin Mux Select 13 | UART0 Receive | |||
| Pin Mux Select 14 | NAND Data Bit 15 | |||
| Pin Mux Select 15 See Note 18. |
GPIO0 Bit 23 | |||
| HPS_Shared_Q3_1 | I/O | Pin Mux Select 3 | SPIM 1 Clock | If unused, program it in the Intel® Quartus® Prime software as an input with a weak pull-up. |
| Pin Mux Select 8 | EMAC 1 Transmit Clock | |||
| Pin Mux Select 13 | UART 0 Clear to Send See Note 19. |
|||
| Pin Mux Select 14 | NAND Data Bit 0 | |||
| Pin Mux Select 15 See Note 18. |
GPIO 1 Bit 0 | |||
| HPS_Shared_Q3_2 | I/O | Pin Mux Select 3 | SPIM 1 Master Out Slave In | If unused, program it in the Intel® Quartus® Prime software as an input with a weak pull-up. |
| Pin Mux Select 8 | EMAC 1 Transmit Control | |||
| Pin Mux Select 13 | UART 0 Request to Send See Note 19. |
|||
| Pin Mux Select 14 | NAND Data Bit 1 | |||
| Pin Mux Select 15 See Note 18. |
GPIO 1 Bit 1 | |||
| HPS_Shared_Q3_3 | I/O | Pin Mux Select 0 | I2C0 Serial Data | If unused, program it in the Intel® Quartus® Prime software as an input with a weak pull-up. |
| Pin Mux Select 3 | SPIM1 Master In Slave Out | |||
| Pin Mux Select 8 | EMAC1 Receive Clock | |||
| Pin Mux Select 13 | UART0 Transmit | |||
| Pin Mux Select 14 | NAND Write Enable See Note 19. |
|||
| Pin Mux Select 15 See Note 18. |
GPIO1 Bit 2 | |||
| HPS_Shared_Q3_4 | I/O | Pin Mux Select 0 | I2C 0 Serial Clock | If unused, program it in the Intel® Quartus® Prime software as an input with a weak pull-up. |
| Pin Mux Select 3 | SPIM 1 Slave Select 0 See Note 19. |
|||
| Pin Mux Select 8 | EMAC 1 Receive Control | |||
| Pin Mux Select 13 | UART 0 Receive | |||
| Pin Mux Select 14 | NAND Read Enable See Note 19. |
|||
| Pin Mux Select 15 See Note 18. |
GPIO 1 Bit 3 | |||
| HPS_Shared_Q3_5 | I/O | Pin Mux Select 2 | SPIS 1 Clock | If unused, program it in the Intel® Quartus® Prime software as an input with a weak pull-up. |
| Pin Mux Select 3 | SPIM 1 Slave Select 1 See Note 19. |
|||
| Pin Mux Select 8 | EMAC 1 Transmit Data Bit 0 | |||
| Pin Mux Select 13 | UART 1 Clear to Send See Note 19. |
|||
| Pin Mux Select 14 | NAND Write Protect See Note 19. |
|||
| Pin Mux Select 15 See Note 18. |
GPIO 1 Bit 4 | |||
| HPS_Shared_Q3_6 | I/O | Pin Mux Select 2 | SPIS 1 Master Out Slave In | If unused, program it in the Intel® Quartus® Prime software as an input with a weak pull-up. |
| Pin Mux Select 8 | EMAC 1 Transmit Data Bit 1 | |||
| Pin Mux Select 13 | UART 1 Request to Send See Note 19. |
|||
| Pin Mux Select 14 | NAND Data Bit 2 | |||
| Pin Mux Select 15 See Note 18. |
GPIO 1 Bit 5 | |||
| HPS_Shared_Q3_7 | I/O | Pin Mux Select 0 | I2C 1 Serial Data | If unused, program it in the Intel® Quartus® Prime software as an input with a weak pull-up. |
| Pin Mux Select 2 | SPIS 1 Slave Select 0 See Note 19. |
|||
| Pin Mux Select 8 | EMAC 1 Receive Data Bit 0 | |||
| Pin Mux Select 13 | UART 1 Transmit | |||
| Pin Mux Select 14 | NAND Data Bit 3 | |||
| Pin Mux Select 15 See Note 18. |
GPIO 1 Bit 6 | |||
| HPS_Shared_Q3_8 | I/O | Pin Mux Select 0 | I2C 1 Serial Clock | If unused, program it in the Intel® Quartus® Prime software as an input with a weak pull-up. |
| Pin Mux Select 2 | SPIS 1 Master In Slave Out | |||
| Pin Mux Select 8 | EMAC 1 Receive Data Bit 1 | |||
| Pin Mux Select 13 | UART 1 Receive | |||
| Pin Mux Select 14 | NAND Command Latch Enable | |||
| Pin Mux Select 15 See Note 18. |
GPIO 1 Bit 7 | |||
| HPS_Shared_Q3_9 | I/O | Pin Mux Select 0 | I2C EMAC 2 Serial Data | If unused, program it in the Intel® Quartus® Prime software as an input with a weak pull-up. |
| Pin Mux Select 1 | EMAC 2 MDIO | |||
| Pin Mux Select 2 | SPIS 0 Clock | |||
| Pin Mux Select 8 | EMAC 1 Transmit Data Bit 2 | |||
| Pin Mux Select 14 | NAND Data Bit 4 | |||
| Pin Mux Select 15 See Note 18. |
GPIO 1 Bit 8 | |||
| HPS_Shared_Q3_10 | I/O | Pin Mux Select 0 | I2C EMAC 2 Serial Clock | If unused, program it in the Intel® Quartus® Prime software as an input with a weak pull-up. |
| Pin Mux Select 1 | EMAC 2 MDC | |||
| Pin Mux Select 2 | SPIS 0 Master Out Slave In | |||
| Pin Mux Select 8 | EMAC 1 Transmit Data Bit 3 | |||
| Pin Mux Select 14 | NAND Data Bit 5 | |||
| Pin Mux Select 15 See Note 18. |
GPIO 1 Bit 9 | |||
| HPS_Shared_Q3_11 | I/O | Pin Mux Select 0 | I2C EMAC 0 Serial Data | If unused, program it in the Intel® Quartus® Prime software as an input with a weak pull-up. |
| Pin Mux Select 1 | EMAC 0 MDIO | |||
| Pin Mux Select 2 | SPIS 0 Slave Select 0 See Note 19. |
|||
| Pin Mux Select 8 | EMAC 1 Receive Data Bit 2 | |||
| Pin Mux Select 14 | NAND Data Bit 6 | |||
| Pin Mux Select 15 See Note 18. |
GPIO 1 Bit 10 | |||
| HPS_Shared_Q3_12 | I/O | Pin Mux Select 0 | I2C EMAC 0 Serial Clock | If unused, program it in the Intel® Quartus® Prime software as an input with a weak pull-up. |
| Pin Mux Select 1 | EMAC 0 MDC | |||
| Pin Mux Select 2 | SPIS 0 Master In Slave Out | |||
| Pin Mux Select 8 | EMAC 1 Receive Data Bit 3 | |||
| Pin Mux Select 14 | NAND Data Bit 7 | |||
| Pin Mux Select 15 See Note 18. |
GPIO 1 Bit 11 | |||
| HPS_Shared_Q4_1 | I/O | Pin Mux Select 0 | I2C 1 Serial Data | If unused, program it in the Intel® Quartus® Prime software as an input with a weak pull-up. |
| Pin Mux Select 4 | SDMMC Data Bit 0 | |||
| Pin Mux Select 8 | EMAC 2 Transmit Clock | |||
| Pin Mux Select 14 | NAND Address Latch Enable | |||
| Pin Mux Select 15 See Note 18. |
GPIO 1 Bit 12 | |||
| HPS_Shared_Q4_2 | I/O | Pin Mux Select 0 | I2C 1 Serial Clock | If unused, program it in the Intel® Quartus® Prime software as an input with a weak pull-up. When you are using this pin as the NAND Ready/Busy input, connect this pin through a pull-up resistor to the VCCIO_2L in the dedicated I/O bank which the NAND_RB pin resides. For more information of the pull-up resistor value, refer to the NAND flash specification. |
| Pin Mux Select 4 | SDMMC Command Line | |||
| Pin Mux Select 8 | EMAC 2 Transmit Control | |||
| Pin Mux Select 14 | NAND Ready/ Busy | |||
| Pin Mux Select 15 See Note 18. |
GPIO 1 Bit 13 | |||
| HPS_Shared_Q4_3 | I/O | Pin Mux Select 4 | SDMMC Clock Out | If unused, program it in the Intel® Quartus® Prime software as an input with a weak pull-up. |
| Pin Mux Select 8 | EMAC 2 Receive Clock | |||
| Pin Mux Select 13 | UART 1 Transmit | |||
| Pin Mux Select 14 | NAND Chip Enable See Note 19. |
|||
| Pin Mux Select 15 See Note 18. |
GPIO 1 Bit 14 | |||
| HPS_Shared_Q4_4 | I/O | Pin Mux Select 4 | SDMMC Data Bit 1 | If unused, program it in the Intel® Quartus® Prime software as an input with a weak pull-up. |
| Pin Mux Select 8 | EMAC 2 Receive Control | |||
| Pin Mux Select 12 | Trace clock | |||
| Pin Mux Select 13 | UART 1 Receive | |||
| Pin Mux Select 15 See Note 18. |
GPIO 1 Bit 15 | |||
| HPS_Shared_Q4_5 | I/O | Pin Mux Select 4 | SDMMC Data Bit 2 | If unused, program it in the Intel® Quartus® Prime software as an input with a weak pull-up. |
| Pin Mux Select 8 | EMAC 2 Transmit Data Bit 0 | |||
| Pin Mux Select 12 | QSPI Slave Select 2 | |||
| Pin Mux Select 13 | UART 1 Clear to Send See Note 19. |
|||
| Pin Mux Select 14 | NAND Data Bit 8 | |||
| Pin Mux Select 15 See Note 18. |
GPIO 1 Bit 16 | |||
| HPS_Shared_Q4_6 | I/O | Pin Mux Select 3 | SPIM 0 Slave Select 1 See Note 19. |
If unused, program it in the Intel® Quartus® Prime software as an input with a weak pull-up. |
| Pin Mux Select 4 | SDMMC Data Bit 3 | |||
| Pin Mux Select 8 | EMAC 2 Transmit Data Bit 1 | |||
| Pin Mux Select 12 | QSPI Slave Select 3 | |||
| Pin Mux Select 13 | UART 1 Request to Send See Note 19. |
|||
| Pin Mux Select 14 | NAND Data Bit 9 | |||
| Pin Mux Select 15 See Note 18. |
GPIO 1 Bit 17 | |||
| HPS_Shared_Q4_7 | I/O | Pin Mux Select 0 | I2C EMAC 1 Serial Data | If unused, program it in the Intel® Quartus® Prime software as an input with a weak pull-up. |
| Pin Mux Select 1 | EMAC 1 MDIO | |||
| Pin Mux Select 3 | SPIM 0 Master In Slave Out | |||
| Pin Mux Select 4 | SDMMC Data Bit 4 | |||
| Pin Mux Select 8 | EMAC 2 Receive Data Bit 0 | |||
| Pin Mux Select 14 | NAND Data Bit 10 | |||
| Pin Mux Select 15 See Note 18. |
GPIO 1 Bit 18 | |||
| HPS_Shared_Q4_8 | I/O | Pin Mux Select 0 | I2C EMAC 1 Serial Clock | If unused, program it in the Intel® Quartus® Prime software as an input with a weak pull-up. |
| Pin Mux Select 1 | EMAC 1 MDC | |||
| Pin Mux Select 3 | SPIM 0 Slave Select 0 See Note 19. |
|||
| Pin Mux Select 4 | SDMMC Data Bit 5 | |||
| Pin Mux Select 8 | EMAC 2 Receive Data Bit 1 | |||
| Pin Mux Select 13 | Trace Clock | |||
| Pin Mux Select 14 | NAND Data Bit 11 | |||
| Pin Mux Select 15 See Note 18. |
GPIO 1 Bit 19 | |||
| HPS_Shared_Q4_9 | I/O | Pin Mux Select 0 | I2C EMAC 2 Serial Data | If unused, program it in the Intel® Quartus® Prime software as an input with a weak pull-up. |
| Pin Mux Select 2 | SPIS 1 Clock | |||
| Pin Mux Select 3 | SPIM 0 Clock | |||
| Pin Mux Select 4 | SDMMC Data Bit 6 | |||
| Pin Mux Select 8 | EMAC 2 Transmit Data Bit 2 | |||
| Pin Mux Select 12 | Trace Data 0 | |||
| Pin Mux Select 14 | NAND Data Bit 12 | |||
| Pin Mux Select 15 See Note 18. |
GPIO 1 Bit 20 | |||
| HPS_Shared_Q4_10 | I/O | Pin Mux Select 0 | I2C EMAC 2 Serial Clock | If unused, program it in the Intel® Quartus® Prime software as an input with a weak pull-up. |
| Pin Mux Select 2 | SPIS 1 Master Out Slave In | |||
| Pin Mux Select 3 | SPIM 0 Master Out Slave In | |||
| Pin Mux Select 4 | SDMMC Data Bit 7 | |||
| Pin Mux Select 8 | EMAC 2 Transmit Data Bit 3 | |||
| Pin Mux Select 12 | Trace Data 1 | |||
| Pin Mux Select 14 | NAND Data Bit 13 | |||
| Pin Mux Select 15 See Note 18. |
GPIO 1 Bit 21 | |||
| HPS_Shared_Q4_11 | I/O | Pin Mux Select 0 | I2C EMAC 0 Serial Data | If unused, program it in the Intel® Quartus® Prime software as an input with a weak pull-up. |
| Pin Mux Select 1 | EMAC 0 MDIO | |||
| Pin Mux Select 2 | SPIS 1 Slave Select 0 See Note 19. |
|||
| Pin Mux Select 3 | SPIM 0 Master In Slave Out | |||
| Pin Mux Select 8 | EMAC 2 Receive Data Bit 2 | |||
| Pin Mux Select 12 | Trace Data 2 | |||
| Pin Mux Select 14 | NAND Data Bit 14 | |||
| Pin Mux Select 15 See Note 18. |
GPIO 1 Bit 22 | |||
| HPS_Shared_Q4_12 | I/O | Pin Mux Select 0 | I2C EMAC 0 Serial Clock | If unused, program it in the Intel® Quartus® Prime software as an input with a weak pull-up. |
| Pin Mux Select 1 | EMAC 0 MDC | |||
| Pin Mux Select 2 | SPIS 1 Master In Slave Out | |||
| Pin Mux Select 3 | SPIM 0 Slave Select 0 See Note 19. |
|||
| Pin Mux Select 8 | EMAC 2 Receive Data Bit 3 | |||
| Pin Mux Select 12 | Trace Data 3 | |||
| Pin Mux Select 14 | NAND Data Bit 15 | |||
| Pin Mux Select 15 See Note 18. |
GPIO 1 Bit 23 |