Agilex™ 7 Clocking and PLL User Guide: M-Series

Download PDF
ID 769001
Date 4/01/2024
Public
Document Table of Contents
Document Table of Contents x
1. Agilex™ 7 FPGA M-Series Clocking and PLL Overview 2. M-Series Clocking and PLL Architecture and Features 3. M-Series Clocking and PLL Design Considerations 4. Clock Control Intel® FPGA IP Core 5. IOPLL Intel® FPGA IP Core 6. Agilex™ 7 Clocking and PLL User Guide: M-Series Archives 7. Document Revision History for the Agilex™ 7 Clocking and PLL User Guide: M-Series
1. Agilex™ 7 FPGA M-Series Clocking and PLL Overview x
1.1. Clock Networks Overview 1.2. PLLs Overview
2. M-Series Clocking and PLL Architecture and Features x
2.1. Clock Networks Architecture and Features 2.2. PLLs Architecture and Features
2.1. Clock Networks Architecture and Features x
2.1.1. Clock Network Architecture 2.1.2. Clock Resources 2.1.3. Clock Control Features
2.1.1. Clock Network Architecture x
2.1.1.1. Clock Network Hierarchy 2.1.1.2. Clock Sectors 2.1.1.3. Programmable Clock Routing
2.1.3. Clock Control Features x
2.1.3.1. Clock Gating 2.1.3.2. Clock Divider
2.1.3.1. Clock Gating x
2.1.3.1.1. Root Clock Gate 2.1.3.1.2. Sector Clock Gate 2.1.3.1.3. I/O PLL Clock Gate 2.1.3.1.4. LAB Clock Gate
2.2. PLLs Architecture and Features x
2.2.1. PLL Features 2.2.2. PLL Usage 2.2.3. PLL Locations 2.2.4. PLL Architecture 2.2.5. PLL Control Signals 2.2.6. PLL Feedback Modes 2.2.7. Clock Multiplication and Division 2.2.8. Programmable Phase Shift 2.2.9. Programmable Duty Cycle 2.2.10. PLL Cascading 2.2.11. PLL Input Clock Switchover 2.2.12. PLL Reconfiguration and Dynamic Phase Shift 2.2.13. PLL Calibration
2.2.5. PLL Control Signals x
2.2.5.1. Reset 2.2.5.2. Locked
2.2.6. PLL Feedback Modes x
2.2.6.1. Direct Compensation Mode 2.2.6.2. LVDS Compensation Mode 2.2.6.3. Source Synchronous Compensation Mode 2.2.6.4. Normal Compensation Mode 2.2.6.5. Zero-Delay Buffer Mode 2.2.6.6. External Feedback Mode
2.2.11. PLL Input Clock Switchover x
2.2.11.1. Automatic Switchover 2.2.11.2. Automatic Switchover with Manual Override 2.2.11.3. Manual Clock Switchover
2.2.13. PLL Calibration x
2.2.13.1. Power-Up Calibration 2.2.13.2. User Calibration 2.2.13.3. Static Phase Error Calibration 2.2.13.4. Output Clock Duty Cycle Correction
3. M-Series Clocking and PLL Design Considerations x
3.1. Guidelines: Clock Switchover 3.2. Guidelines: Timing Closure 3.3. Guidelines: Resetting the PLL 3.4. Guidelines: Configuration Constraints 3.5. Clocking Constraints 3.6. IP Core Constraints 3.7. Guideline: Achieving 5% Duty Cycle for fOUT_EXT ≥ 300 MHz Using tx_outclk Port from LVDS SERDES Intel® FPGA IP
4. Clock Control Intel® FPGA IP Core x
4.1. Release Information for Clock Control Intel® FPGA IP 4.2. Clock Control Intel® FPGA IP Core Parameters 4.3. Clock Control Intel® FPGA IP Core Ports and Signals
5. IOPLL Intel® FPGA IP Core x
5.1. Release Information for IOPLL Intel® FPGA IP 5.2. IOPLL IP Core Parameters 5.3. IOPLL IP Core Ports and Signals
5.2. IOPLL IP Core Parameters x
5.2.1. IOPLL IP Core Parameters - PLL Tab 5.2.2. IOPLL IP Core Parameters - Settings Tab 5.2.3. IOPLL IP Core Parameters - Cascading Tab 5.2.4. IOPLL IP Core Parameters - Advanced Parameters Tab
1. Agilex™ 7 FPGA M-Series Clocking and PLL Overview
2. M-Series Clocking and PLL Architecture and Features
3. M-Series Clocking and PLL Design Considerations
4. Clock Control Intel® FPGA IP Core
5. IOPLL Intel® FPGA IP Core
6. Agilex™ 7 Clocking and PLL User Guide: M-Series Archives
7. Document Revision History for the Agilex™ 7 Clocking and PLL User Guide: M-Series

5.2.2. IOPLL IP Core Parameters - Settings Tab

Table 9.   IOPLL IP Core Parameters - Settings Tab for M-Series Devices
Parameter Value Description
PLL Auto Reset On or Off Automatically self-resets the PLL on loss of lock.
Create a second input clk ‘refclk1’ On or Off Turn on to provide a backup clock attached to your PLL that can switch with your original reference clock.
Second Reference Clock Frequency 14 0 — Selects the frequency of the second input clock signal. The default value is 100.0 MHz. The minimum and maximum value is dependent on the device used.
Create an ‘active_clk’ signal to indicate the input clock in use 0 On or Off Turn on to create the activeclk output. The activeclk output indicates the input clock which is in use by the PLL. Output signal low indicates refclk and output signal high indicates refclk1.
Create a ‘clkbad’ signal for each of the input clocks 0 On or Off Turn on to create two clkbad outputs, one for each input clock. Output signal low indicates the clock is working and output signal high indicates the clock is not working.
Switchover Mode 0 Automatic Switchover, Manual Switchover, or Automatic Switchover with Manual Override Specifies the switchover mode for design application. The IP supports three switchover modes:
  • If you select the Automatic Switchover mode, the PLL circuitry monitors the selected reference clock. If one clock stops, the circuit automatically switches to the backup clock in a few clock cycles and updates the status signals, clkbad and activeclk.
  • If you select the Manual Switchover mode, when the control signal, extswitch, changes from logic high to logic low, and stays low for at least three clock cycles, the input clock switches to the other clock. The extswitch can be generated from FPGA core logic or input pin.
  • If you select Automatic Switchover with Manual Override mode, when the extswitch signal is high, it overrides the automatic switch function. As long as extswitch remains high, further switchover action is blocked. To select this mode, your two clock sources must be running and the frequency of the two clocks cannot differ by more than 20%. If both clocks are not on the same frequency, but their period difference is within 20%, the clock loss detection block detects the lost clock. The PLL most likely drops out of lock after the PLL clock input switchover and needs time to lock again.
Enable access to I/O Bank clock ports On or Off This options enables the IOPLL's I/O bank clock ports. The ports are exported instead of outclks, and can be configured through corresponding outclk settings (the outclks that correspond to periphery ports are indicated in the 'Output Clocks' section). The clock ports can be connected to one LVDS only
Enable access to the PLL DPA output port 0 On or Off Turn on to enable the PLL DPA output port.
Enable access to PLL external clock output port On or Off Turn on to enable the PLL external clock output port.
Specifies which outclk to be used as extclk_out[0] source C0–C3 (I/O bank) Specifies the outclk port to be used as extclk_out[0] source.
Specifies which outclk to be used as extclk_out[1] source C0–C3 (I/O bank) Specifies the outclk port to be used as extclk_out[1] source.
14 This parameter is only available when Create a second input clk 'refclk1' is turned on.
Level Two Title