Agilex™ 7 FPGA M-Series HBM2e Development Kit User Guide

Download PDF
ID 782461
Date 5/14/2024
Public
Document Table of Contents
Document Table of Contents x
1. Overview 2. Getting Started 3. Development Kit Setup 4. Board Test System 5. Development Kit Hardware and Configuration 6. Custom Projects for the Development Kit 7. Document Revision History for the Agilex™ 7 FPGA M-Series HBM2e Development Kit User Guide A. Development Kit Components B. Additional Information
1. Overview x
1.1. Block Diagram 1.2. Feature Summary 1.3. Box Contents 1.4. Recommended Operating Conditions
2. Getting Started x
2.1. Quartus® Prime Software and Driver Installation 2.2. Design Examples
3. Development Kit Setup x
3.1. Default Settings 3.2. Powering Up the Development Kit 3.3. Performing Board Restore
3.3. Performing Board Restore x
3.3.1. Restoring Board QSPI Flash with Default Factory Image
4. Board Test System x
4.1. Setting Up the BTS GUI Running Environment 4.2. Testing the Functionality of the Development Kit 4.3. Controlling the On-board Clock through Clock Controller GUI 4.4. Monitoring On-Board Power Regulator through Power Monitor GUI 4.5. Identifying Test Pass or Fail-based on BTS GUI Test Status
4.1. Setting Up the BTS GUI Running Environment x
4.1.1. Downloading OpenJDK 4.1.2. Downloading OpenJFX 4.1.3. Installing OpenJDK and OpenJFX 4.1.4. Installing the Quartus® Prime Software 4.1.5. Running the BTS GUI
4.2. Testing the Functionality of the Development Kit x
4.2.1. The Bottom Information Bar 4.2.2. The Configure Menu 4.2.3. The Sys Info Tab 4.2.4. The GPIO Tab 4.2.5. The XCVR Tab
4.2.5. The XCVR Tab x
4.2.5.1. The QSFPDD NRZ Tab 4.2.5.2. The QSFPDD PAM4 Tab 4.2.5.3. The FMC+ NRZ Tab 4.2.5.4. The QSFPDD800 PAM4 Tab
4.3. Controlling the On-board Clock through Clock Controller GUI x
4.3.1. Si5391-1 4.3.2. Si5391-2 4.3.3. Si5392 4.3.4. Si5395 4.3.5. Si5332 4.3.6. Si5518
5. Development Kit Hardware and Configuration x
5.1. Configure FPGA and Access HPS Debug Access Port by JTAG 5.2. Configure the FPGA Device Using the Avalon® streaming interface x8 configuration Mode 5.3. Daughter Card
5.3. Daughter Card x
5.3.1. HPS Out of Box Experience (OOBE) Daughter Card
6. Custom Projects for the Development Kit x
6.1. Add SmartVID Settings in the Quartus® Prime QSF File 6.2. Golden Top
A. Development Kit Components x
A.1. Power A.2. Clocks A.3. General Input/Output A.4. Memory Interfaces A.5. Communication Interfaces A.6. Daughter Card A.7. Connectors and Cables
B. Additional Information x
B.1. Safety and Regulatory Information B.2. Compliance Information
B.1. Safety and Regulatory Information x
B.1.1. Safety Warnings B.1.2. Safety Cautions
1. Overview
2. Getting Started
3. Development Kit Setup
4. Board Test System
5. Development Kit Hardware and Configuration
6. Custom Projects for the Development Kit
7. Document Revision History for the Agilex™ 7 FPGA M-Series HBM2e Development Kit User Guide
A. Development Kit Components
B. Additional Information

5.2. Configure the FPGA Device Using the Avalon® streaming interface x8 configuration Mode

  1. Set S24 to Avalon® streaming interface x8 configuration mode first.
  2. Default MAX® 10 image and hardware design supports the Avalon® streaming interface x8 configuration mode only.
  3. Power on the board, use push button S2 to choose page, and S1 to configure the FPGA.
  4. Default page is 0.
Level Two Title