E-tile Hard IP Intel® Stratix® 10 Design Examples User Guide: Ethernet, CPRI PHY, and Dynamic Reconfiguration

ID 683578
Date 3/06/2022
Public

A newer version of this document is available. Customers should click here to go to the newest version.

Document Table of Contents

4.3.6. Dynamic Reconfiguration Flow for 24G CPRI FEC to 24G CPRI Non-FEC

This section provides a sequential flow for dynamic reconfiguration of 24G CPRI FEC configuration to 24G CPRI Non-FEC configuration. For other variations, you can refer to the generated C file that provides comprehensive information through comments.
  1. Assert the i_sl_tx_rst_n and i_sl_rx_rst_n reset signals.
  2. Disable Serdes (via PMA attribute code 0x0001). For more information, refer to the E-Tile Transceiver PHY User Guide.
  3. Perform PMA Analog Reset. For more information, refer to the E-Tile Transceiver PHY User Guide.
  4. Change the following registers:
    Table 39.  Registers: 24G CPRI FEC to 24G CPRI Non-FEC
    Block Configuration Registers Offset Register Bits From Value To Value
    ELANE txmac_ehip_cfg 0x40B am_width [5:3] 3’b100 3’b001
    phy_ehip_pcs_modes 0x30E use_aligner [9] 1’b0 1’b1
    cpri_rate_sel 0xC00 - 1B B
    RS-FEC rsfec_top_clk_cfg 0x005 fec_lane_ena [3:0] 4’bxxx1 4’bxxx0
    rsfec_top_rx_cfg 0x014 core_rx_out_sel0 [1:0] 2’b01 2’b00
    Transceiver xcvrif_ctrl0 (0x4) 0x004 cfg_tx_data_in_sel [4:2] 2’b01 2’b00
    xcvrif_ctrl0 (0x5) 0x005 cfg_clk_en_fec_d2_tx [13] 1’b1 1’b0
    cfg_clk_en_pcs_d2_tx [12] 1’b0 1’b1
    xcvrif_ctrl0 (0x7) 0x007 cfg_rx_fifo_clk_sel [30:29] 2’b00 2’b10
    xcvrif_ctrl0 (0x37) 0x037 rxbit_cntr_pma [7] 1’b0 1’b1
    cfg_rx_bit_counter_rollover 0x036, 0x035, 0x034 - 13‘d5248 ('h1480) 13'd6304 (‘h18A0)
  5. Adjust the phase offset of a recovered clock using the RX Phase Slip (via PMA attribute code 0x000E). For more information, refer to the E-Tile Transceiver PHY User Guide.
  6. Enable Serdes (via PMA attribute code 0x0001). For more information, refer to the E-Tile Transceiver PHY User Guide.
  7. Enable internal serial loopback (via PMA attribute code 0x0008). For more information, refer to the E-Tile Transceiver PHY User Guide.
  8. Deassert the i_sl_tx_rst_n and i_sl_rx_rst_n reset signals.
  9. Wait until:
    PIO_OUT[3:0] = 0x7 (o_sl_rx_pcs_ready, o_sl_rx_block_lock, o_ehip_ready asserted)
  10. Clear ELANE statistic counters.
  11. Enable packet generator to start sending packets. Wait for 100us.
  12. Check for checker_pass status, wait until:
    PIO_OUT[4:0] = 0xF (checker_pass, o_sl_rx_pcs_ready, o_sl_rx_block_lock, o_ehip_ready asserted)
  13. Disable packet generator to stop sending packet.